[easy_image_gallery gallery="589"]
[easy_image_gallery gallery="851"]
Type A1
Spirals to right and left joined together by a crimped rod.
A: 0,90 - 6* // B: 3 - 45 // C: 1 - 7 // D: 5 - 100
Max width (m): 6
The spiral wire section may also be laminated to achieve a flat surface.
Accessories
[easy_image_gallery gallery="424"]
Type A2
Double spiral to right and left joined together by a straight or crimped rod.
A: 0,90 - 4* // B: 3 - 15 // C: 1 - 4 // D: 5 - 27
Max Width (m): 6
The spiral wire section may also be laminated to achieve a flat surface.
Accessories
[easy_image_gallery gallery="362"]
Type A3-A4-A5-A6
Spirals to right and left joined together by pre-crimped rods. There can be 3, 4, 5 or 6 rods through every spiral to make types A3, A4, A5 and A6 respectively.
A: 0,50 - 4* // B: 3 - 20 // C: 0,90 - 5 // D: 2 - 6,5
Max width (m): 6
The spiral wire section may also be laminated to achieve a flat surface.
Accessories
[easy_image_gallery gallery="442"]
Type B
Groups of spirals in a single direction (right or left) screwed together. They may also be assembled in stretches in alternating directions.
A: 0,50 - 4* // B: 10 - 60 // C: - // D: -
Max width (m): 4
The spiral wire section may also be laminated to achieve a flat surface.
[easy_image_gallery gallery="288"]
Type B1
Groups of spirals in a single direction (right or left) screwed together and assembled in stretches, and with a reinforcing cross rod between each pair of spirals at their contact point; the groups of spirals may be assembled in sections of alternating directions.
The spiral wire section may also be laminated to achieve a flat surface.
Accessories
[easy_image_gallery gallery="817"]
Type B2
Groups of double spirals in a single direction (right or left) screwed together and assembled in stretches, and with a reinforcing cross rod between each pair of spirals at their contct point; the groups of spirals may be assembled in sections of alternating directions.
A: 0,50 - 3,20* // B: 2 - 10 // C: 0,80 - 5 // D: 3,20 - 25
Max width (m): 4
The spiral wire section may also be laminated to achieve a flat surface.
Types of belt edge
Accessories
[easy_image_gallery gallery="940"]
Type Fil-Pla
Belts formed by vertical flatbars folded alternately, assembled by means of double or simple cross bars.
A: 12 - 1,20* // B: 44,64 // C: 4 // D: 27,92
Max width (m): 4
To evenly distribute several sprockets across the width of the belt, depending on the specific width. The sprockets must press on the cross rods and not on the laminated metal band.
Type Vaucanson
Belts made up of parallel rods in steps, assembled by side loops.
A: - // B: - // C: 4,50 - 6 // D: 15,87 - 25,40
Max width (m): 1
This type of belt is also produced forming curves with different pitches (internal and external).
Accessories
[easy_image_gallery gallery="450"]
Type Inter linked wire rods
Belts are made with cross wire strands in alternating rectangular shaped and weaved together forming an interlinked flexible belt. This type of belt provides positive traction via pulling sprockets. Simple or double edge.
A: - // B: - // C: 0,90 - 3 // D: 4 - 14
Max width (m): 3
Usually produced in stainless steel.
Types of belt edge
Tipo Alveolar
Cinta transportadora modelo Alveolar, con varillas paralelas en escalón, ensambladas mediante bucles laterales.
A: - // B: - // C: 4,50 - 6 // D: 15,87 - 25,40
Ancho máximo (m): 1
Este modelo de cinta también se fabrica, formando curva con diferentes pasos (interior y exterior).
